![]() Most of the led ceiling light panel is with 2835SMD chips, and SMD5630 chips are popular if customers request to do higher lumens output. ![]() and the led chips generally are SMD2835, SMD4014, SMD5630. ![]() LED chips on PCB.PCB is aluminum material with a copper circuit. some special light Guide plates are Anti-glare, it is a key material to do Anti-glare led panel lights UGR<19. Our ultra-thin led panel lights never use a structure light guide plate. On the market prone to yellowing panel lights are generally used with the structure of the light guide plate. Under the condition of budget permission, the light guide plate with laser point shall be selected as far as possible. The diffuser plate generally is PS materials, the thickness is 1.0mm 1.2mm, and 1.5mm optional thicker, the more expensive the price, the better the effect. and the thickness of the light guide plate is 1.0mm,1.2mm,1.5mm,2.0mm, and 3.0mm. The difference between price and quality is the laser dot light guide plate > ink light guide plate > structure light guide plate. The light guide plate on the market is mainly divided into three categories, laser dot light guide plate, ink printing light guide plate, structure light guide plate. There will be no dark spots, water ripples, etc. The use of a high-quality light guide plate can make the finished light panel emitting more evenly. The quality of the light guide plate is one of the most important factors to determine the quality of LED flat panel light. The black frame can also be customized, but often the price will be more expensive than the other two colors. The original led panel light solutions are only with 6063 aluminum frame, It is usually anodized, the surface is very flat, the conventional color is silver, usually, many customers on the market will need a white frame. PLEASE ASK IF YOU REQUIRE DIMMING FOR THIS PRODUCT.įor more information on dimming, please check out our LED Panel Dimming Guide, or for more information call us on 01652 638850 and ask to speak with one of our fully qualified electricians.It is important for everyone to know the materials for led panel light, which are basic requirements to know how to choose a high-quality product.įrame(shell). 3) TRIAC dimming - witha conventional wall mounted TRIAC dimmer switch using your existing wiring. 2) 1-10V dimming - using a 2.4GHz RF remote control and 1-10V dimmer controller. Optional dimming can be achieved by either of the following 3 methods: 1) 1-10V dimming - using a wall mounted 1-10v dimmer switch (please note that control wires are required from the dimmable driver to the switch). These provide over 3 hours of maintained light output without the additional expense and inconvenience of separate emergency lighting. To ensure that the panel doesn't have dark spots special lenses are fitted over each LED, while to ensure the durability of the automated LED fixing process each PCB is tested to withstand a downwards pull force of 850g for 30 days at operating temperature.Įmergency Packs are available, which are British designed and manufactured specifically for our panels. ![]() However, in most cases this does not matter as there usually plenty of space above the ceiling grid to allow installation. The only noticeable difference between this Back Lit LED panel and our Edge Lit LED panels is that being 32mm it is a little thicker than our Edge Lit panels which are 10mm. This LGP is relatively expensive and absorbs some light, meaning that back lit panels, which do not require an LGP, have a cost and also efficiacy advantage over Edge Lit panels. (Most LED panels are "edge lit" which means that the LEDs are fitted in the edge of the panel and shine light towards the centre of the panel, where a special plastic component called a Light Guide Plate (LGP) "pushes" the light out of the front of the panel. The secret behind the incredible low price, but high performance of this panel is that it is "back lit", which means that the LEDs are affixed to the back of the panel and emit light towards the front of the panel. The panels have a durable white powder coated aluminium frame, which will match white ceiling grids perfectly. The DC connection to the panel is plug-and-play for ease of installation, and the AC is simply wired into the existing lighting circuit via a live and neutral. which is at least as much light as it's fluorescent counterpart.įor peace of mind this LED panel comes complete with a 30W Tridonic Flicker-Free driver. The low cost comes with a surprisingly impressive 125lm/W efficacy to give 3750lm of light. Our NEW Back Lit 600mm x 600mm 5000K LED panel lights are ideal as a direct replacement for 600 x 600 four-tube fluorescent modular fittings which are the size most frequently used in offices.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |